WATERMARK® sensors

How does it work ?

Tension is naturally equilibrating beetween the soil and the internal media of the sensor, as soon as the contact with the soil is established. Focus on the importance of the installion technique, to secure a quick and perfect contact (see « Installation »). We measure an internal resistivity, tightly correlated with water tension. The gypsum buffer saturates the internal media, that becomes independant of soil salinity of (up to 3 mS/cm). The incidence of soil temperature (1 % per °C) is automatically compensated, thanks to a soil temperature measure.

Caracteristics

Sensors are rustical, no maintenance, no disconnection, frost resistant. Installation can be enterely underground (on perrenial crops). They offer a good realibility up to 4K measures, high reproductibilty inter-batch, now good accuracy beetween batches. The range of mesaure is from 0 à 239 Cbars (ou KPa).

Kinetics

Behaving of WATERMARK® sensors
A WATERMARK® sensor, correctly installed, is permanently equilibrated with the soil tension. Its own response time is a few seconds. This can easily be verified by playing with sensors out of the soil.

The soil imposes its speed. 

Observing soils can be surprising.
For example, the time needed by certain soils to « come back » from a deep drought, or the time others need to drain, etc …

Including degradation of soil structure, that slows down the natural tension equalization.

Extreme dessication :
We have let a soil dry in our test cylinders to reach an extreme and long lasting drought. To allow observe the behavior of the soil and sensors, during recovery phase. Resulst on batches 2004 and F7 show that Watermark sensors equilibrate without delay and do not keep any memory of the event.

TestsSondes

Sensibility

Watermark® sensors have an excellent sensitivity, comparable to tensiometer’s.
Since 2014, all Monitors (R2-DM, R2-DL, R2-DX, R2-DXS) activate a second measuring circuit, beetween 0 and 30 cbars, to get an excellent sensitivity at low tension end** .  This allows new applications.

** unlike lack of sensibility beetween 0 and 10 cb, that was falsely lended to the sensor, in the 90’s. In fact, dued to the former reading meter.

Longevity

20 years of experience, intensively using more than 200 000 WATERMARK® sensors (ourselves and our customers) , plus systematic testing of sensor batches, gives us recurrent data :
on annual crops, longevity is classicaly of 6 campains of 3-4 months or 5 campains of 5-6 months, or 4000 measures.
On perennial crops, longevity of sensors is 4 entire years or 4000 measures. After, one observes a drift, generally upward.

Variability

WATERMARK® sensor is constituted of natural materials :

  • big avantage for the realism of the measure
  • disavantage is a possible variabilty of row material

In order to handle this variability, we market the same batch of WATERMARK® sensors during  2 to 3 years, knowing that the reproductibility intra-batch is excellent (variability < 5 %).

We launch a new batch, after pre-testing, in order to get a good similarity beetween batches. The batch is then continously tested.

Concerning variability in time, one must renew the sensors, reachning the end of working time, (see longevity), in order to maintain the quality of measure, before degradation.

The annual cost per field or per surface comes out in the lowests of the market. The quality / price being in the bests (see costs).

Correction factor

Not the case of batches now in service, but certain batches need a correction factor. Table of correction factors and longevity, that turns around 4000 / 4500 measures.

Batch marketed Coeff. Annual crop Perrenial crop
F18 mid 2017 – 2018 1.1 Previ : 5 seasons Previ : 4 years
F16 mid 2015 – mid 2017 0.9 Previ : 5 seasons Previ : 4 years
F13 may 2013 – 2014 – mid 2015 1.0 5 seasons 4 years
F11 april 2011 – 2012 – 2013 1.4 6 seasons 4 years
F9 may 2009 – 2010 – 2011 1.0 4 seasons 3 years
F7 2007 – 2008 – 2009 1.1 4 seasons 3 years
F5 2005 – 2006 1.2 6 seasons 4 years
2004 2004 – 2005 1.0 6 seasons 4 years

Performances of  WAYERMARK® sensors allow respond to all technical levels requirements

With Irrometer Co, we constanly improve the of Watermark® sensors, developping new applications, opening new fields.

In Europe, the technical quality standards are high :

  • 6 sensors per field (up to 32) for a minimum statistical reliability
  • a dedicated installing tool for a good installation (essential)
  • mounted sensors for practical aspects in field
  • Batch pre-tested and followed for a good reproductibility
  • On-line graphs and videos for quick and easy interpretations.

Reliability, representavity, accuracy

Top